Reply to Thread New Thread |
![]() |
#1 |
|
One of the usual Indians rolled up the other day but instead of per usual trying to flog off an alternate electronic company he was giving away free (his company would sell Carbon credits to the gubmint) a power board. This has sockets one marked normal, and some master and slaves.
It has a IR chip as well and what happens is after an hour if it doesnt detect any remote control action it will flash for three minutes, if during these three minutes you do not adjust the TV by the remote (he said just move the volume up and down) it will power down the unit completely, no standby. Seems to work ok and even without the standby the TV (50 inch Plasma) seems to start up without waiting too long. My only question is is this equivalent of switching it off at the mains likely to cause any problems with the TVs innards? |
![]() |
![]() |
#2 |
|
|
![]() |
![]() |
#3 |
|
|
![]() |
![]() |
#4 |
|
I reckon it might actually lead to increased electricity use. I wouldnt but I have been in familys where the TV is on a lot and I reckon kiddies will just learn not to turn off TVs (something they struggle with anyway) because it turns itself off. Multiply by millions of TVs in homes with young familys and a habit they will take into adult life…
|
![]() |
![]() |
#5 |
|
I reckon it might actually lead to increased electricity use. I wouldnt but I have been in familys where the TV is on a lot and I reckon kiddies will just learn not to turn off TVs (something they struggle with anyway) because it turns itself off. Multiply by millions of TVs in homes with young familys and a habit they will take into adult life… I have a powerboard with a master socket and several slave sockets, if the power draw through the master socket goes below a certain limit it'll completely cut power to everything on the board. Downside is you need to manually hit the main on/off switch for whatever is in the master socket. |
![]() |
![]() |
#6 |
|
|
![]() |
![]() |
#7 |
|
I don't think it's intended as an alternative to turning it off in the normal way (onto standby with the remote), but more so that after it's been on standby for a while it'll cut the standby power. Once people turn off their lights and ceiling & pedestal fans when they're not in a room, then reducing standby power loads will have a significant effect. |
![]() |
![]() |
#9 |
|
|
![]() |
![]() |
#10 |
|
Which, even though the VoltsCommisioner wouldn't agree, will save sod all power in the scheme of things. I do beleive that every little bit counts, but some bits are so small as to have no effect. I doubt it saves us any noticeable amount of power, but is potentially useful by stopping things being turned on for no reason. |
![]() |
![]() |
#11 |
|
I can't see the economic sense in paying someone to go around giving way free powerboards, which will save bugger all power anyway, just to claim a few cents in carbon credits.
If the carbon credits are valuable enough to make that a business, then why can't I sell them each time I turn something off at the wall too. Also, I should be able to make a killing on the carbon market each time I stop a bushfire. Just sounds like some sort of scam to me. |
![]() |
![]() |
#12 |
|
I can't see the economic sense in paying someone to go around giving way free powerboards, which will save bugger all power anyway, just to claim a few cents in carbon credits. |
![]() |
![]() |
#13 |
|
|
![]() |
![]() |
#14 |
|
As an example of TV power consumption when off a Panasonic plasma TV draws 0.4W so we are not talking big savings here.
The old CRT TVs (remember back when TVs had those large glass bottles in the front?) would often keep the CRT filament warm so they would take less time to warm up. These would chew a few Watts in standby. |
![]() |
![]() |
#15 |
|
|
![]() |
![]() |
#16 |
|
>>>My only question is is this equivalent of switching it off at the mains likely to cause any problems with the TVs innards?
Nope, but would add dodgy sockets with intermittent connections on power boards [especially cheaper ones] aren't good with equipment that draws substantial current. For example take a PA amp which driven to high power will change its clipping threshold with fluctuating mains supply as unit supply rails will be all over the place. My TV when turned off at the mains comes back on on the same channel etc, so is good that way. The two better inverters I use [am on solar with 12Volt system] have variable setting for auto standby, you can adjust the lower current draw detection threshold. Some quiescent current is required for inverter operation, for biasing and such, so it reduces this by auto load detect and auto-standby. There's maybe couple of downsides to this, being slower operation as comes out of standby, and maybe they have to pulse check for load, which of the latter maybe can pulse lights. |
![]() |
Reply to Thread New Thread |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|