LOGO
General Discussion Undecided where to post - do it here.

Reply to Thread New Thread
Old 08-29-2012, 10:22 PM   #1
JohnMitchel

Join Date
Oct 2005
Posts
414
Senior Member
Default Wi fi booster
Anyone have experience in how to get wi fi from the first to second floor using a booster?
JohnMitchel is offline


Old 08-29-2012, 10:47 PM   #2
GentlieGant

Join Date
Oct 2005
Posts
400
Senior Member
Default
Three solutions come to mind:

1. Depending upon the access point (AP) you are using, you may only need to replace the antenna with a hi-gain or upgrad the AP to a newer and more powerful model.
2. Or you can use a wifi repeater that captures your existing (weak) signal, amplifies it and retransmits it. Awkward to use on secure networks, however.
3. Use a range extender like a Linksys RE1000. I match brands because it's often simply easiest to set up.

Check out Networking and Wi-Fi - CNET Reviews to get a set of decent reviews for you to select from!
GentlieGant is offline


Old 08-29-2012, 11:10 PM   #3
agiopwer

Join Date
Oct 2005
Posts
441
Senior Member
Default
could you not also run a cat6 cable into another router?
agiopwer is offline


Old 08-29-2012, 11:42 PM   #4
Ikhqgvas

Join Date
Nov 2005
Posts
496
Senior Member
Default
A fourth option might be a Powerline Extender. Didn't find them at Cecomsa's site but Amazon sells a lot of them
Amazon.com: powerline wireless: Electronics

You plug one in on the 1st floor, connect it to your switch or router, and the 2nd unit you plug in on the 2nd floor. Possible a small config needs to be done to secure and rename the network.
The units need to be on the same power net, they can't for example traverse from your house to your neighbour...

I use this alot in Europe.
Ikhqgvas is offline


Old 08-29-2012, 11:59 PM   #5
Hpdovoxm

Join Date
Oct 2005
Posts
523
Senior Member
Default
Sounds good.... any experience using it here? Anyone?

But, with the wonders reg. "power" here using it here I would not be surprised if my toaster all of a sudden has Internet access, lol...

A fourth option might be a Powerline Extender. Didn't find them at Cecomsa's site but Amazon sells a lot of them
Amazon.com: powerline wireless: Electronics

You plug one in on the 1st floor, connect it to your switch or router, and the 2nd unit you plug in on the 2nd floor. Possible a small config needs to be done to secure and rename the network.
The units need to be on the same power net, they can't for example traverse from your house to your neighbour...

I use this alot in Europe.
Hpdovoxm is offline


Old 08-30-2012, 12:33 AM   #6
Pheddytrourry

Join Date
Oct 2005
Posts
517
Senior Member
Default
Order something like this for your computer (usb)....
New RT3070 802.11b/g/n WiFi 150Mbps Wireless USB Adapter with 30dBi Antenna | eBay
and something like this for your router.....
20dBi 3G WIFI Directional Antenna Aerial WLAN RP-SMA ForModem Router PCI Card | eBay
(don't forget to password your router)
Pheddytrourry is offline


Old 08-30-2012, 12:51 AM   #7
SHpuntik

Join Date
Oct 2005
Posts
608
Senior Member
Default
Providing wireless solutions for this problem here in the DR could be a great business idea for someone.

Because of the building practises here, with all the rebar they use for construction, it's like sitting in a metal cage, which really attenuates any radio signal. You will never get the claimed distances on wireless devices here.

If someone could come up with a device or method of ensuring good wifi coverage throughout a whole building I'm sure it would be a good seller.
SHpuntik is offline


Old 08-30-2012, 12:58 AM   #8
Hpdovoxm

Join Date
Oct 2005
Posts
523
Senior Member
Default
Right, I made the math without the rebar...

Providing wireless solutions for this problem here in the DR could be a great business idea for someone.

Because of the building practises here, with all the rebar they use for construction, it's like sitting in a metal cage, which really attenuates any radio signal. You will never get the claimed distances on wireless devices here.

If someone could come up with a device or method of ensuring good wifi coverage throughout a whole building I'm sure it would be a good seller.
Hpdovoxm is offline


Old 08-30-2012, 01:03 AM   #9
JohnMitchel

Join Date
Oct 2005
Posts
414
Senior Member
Default
Thank to everyone
JohnMitchel is offline


Old 08-30-2012, 10:50 AM   #10
Mjypksun

Join Date
Oct 2005
Posts
468
Senior Member
Default
Sounds good.... any experience using it here? Anyone?

But, with the wonders reg. "power" here using it here I would not be surprised if my toaster all of a sudden has Internet access, lol...
The results vary depending on the quality of wiring and state of it, the amount of electronic crosstraffic and whether or not the phases for the electric groups are matching. Cross phases these solutions loose a lot of practicality.

Uncertain performance was the reason I have just cabled the entire house with a switch right after the router (I assume your router does both Wi-Fi and cabled). I have installed separate routers in each area attached to the cable as needed. This also gives you the opp to set-up different networks (say private and public) for different users.

Don't be cheap on the switch and make sure they are 1G, either-way or else you are loosing half your network capacity.
Mjypksun is offline


Old 08-30-2012, 11:59 PM   #11
Pheddytrourry

Join Date
Oct 2005
Posts
517
Senior Member
Default
Almost all antennas that come with routers are “omnidirectional”. That means they broadcast all the way around (360 degrees)..... but they do so in a flat donut shape. Very little up or down. Thus, a first floor omnidirectional antenna doesn't provide much coverage upstairs. Try tilting the antenna, or as others have suggested.... a second antenna (router/antenna) upstairs.

Others (on the internet) suggest a parabolic aluminum foil reflector, placed behind the antenna (on the side of the exterior wall) will reflect more signal were you want it.
Pheddytrourry is offline


Old 08-31-2012, 08:40 AM   #12
Mjypksun

Join Date
Oct 2005
Posts
468
Senior Member
Default
Almost all antennas that come with routers are “omnidirectional”. That means they broadcast all the way around (360 degrees)..... but they do so in a flat donut shape. Very little up or down. Thus, a first floor omnidirectional antenna doesn't provide much coverage upstairs. Try tilting the antenna, or as others have suggested.... a second antenna (router/antenna) upstairs.

Others (on the internet) suggest a parabolic aluminum foil reflector, placed behind the antenna (on the side of the exterior wall) will reflect more signal were you want it.
Good and cheap tips, from CNET. Start with these here.

I think it has to do with the solidity of the walls though, so the OP will prolly need multiple sources around the premises
Mjypksun is offline



Reply to Thread New Thread

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 

All times are GMT +1. The time now is 05:19 PM.
Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2
Design & Developed by Amodity.com
Copyright© Amodity